Airflex Pro with Built-in Adjustable Magma Instant Heater
From: £3,857.80 Original price was: £3,857.80.£3,295.40Current price is: £3,295.40. plus VAT
Airflex Pro with Built-in Magma Heater
This Airflex Pro is designed for operators who want a professional extractor with built-in heater.
- Pump options from 220 to 600psi
- Powerful 8.4 vac motor system (run up to 100ft hoses)
- Magma heater built into machine’s motor housing
- Choose your colour
- 55 litre tank
- 12″ stair climbing wheels
- Easy tilt-and-roll van loading system
- Built-in auto-feed
- Built-in power pre-spray system
- Optional exhaust silencer
- Free carpet cleaning course included
- Full details below
- Not sure which machine? Check out our Buyers Guide for Professional Carpet Cleaners
Build your machine:
Product Description
Airflex Pro with Built-In Magma Heater
This is a powerful professional extractor designed for users who prefer a machine with built-in heater.
Pump options:
- 130psi standard
- 220psi fully adjustable
- 400psi fully adjustable
- 600psi fully adjustable
Powerful 8.4″ vac motor system
This machine comes with an 8.4″ vacuum system that gives you the power of 2 x 3-stage vac motors (but the newer 8.4″ vac motors are designed to last 3 x longer than the old style 5.7″ motors and have improved moisture protection).
This is a professional spec vacuum system that will deliver professional results and drying times. It will power hose runs up to 100ft.
Built-in Magma ‘instant’ heater
The Airflex Magma heater gives you very hot water straight from stone cold water in the tank with no pre-heating or secondary heater needed.
Just add stone cold water to the tank, wait around 90 seconds for the heater to warm up, then start cleaning. There’s no need to pre-heat the water in the solution tank.
The Magma will give you very hot water at up to 400psi, direct from cold water in the tank.
This is not a cheaper immersion heater (so you won’t need to wait 45 minutes while the water in the tank heats up). The Magma heats the water as you use it. Just add water to the tank, all ow the heater to warm up (about 90 seconds) and start cleaning.
Please note: A built-in heater is best suited to shorter hose runs. The further you are cleaning away from the machine, the greater the heat loss will be as the water travels down the hose. For this reason, if you often run hoses over 50ft regularly, we recommend an unheated Airflex Pro with the external Magma heater, which can be positioned at the wand end of the hose run.
Adjustable heat
The Airflex Magma heater comes with fully adjustable temperature control as standard. So if you are cleaning a heat sensitive fibre simply turn the heat down.
See the Airflex Magma heater in action here
More reasons to choose an Airflex Custom Made:
Large water tanks
The solution tank holds approx 55 litres, so you won’t have to keep stopping to empty and re-fill. Large tanks are all the more important now with the higher performance pump systems. The waste tank has a working capacity of approx 40 litres.
Easy van loading system
Loading and unloading Airflex is very easy. Just tilt Airflex back and roll into your van. There’s no need to lift the machine or install an expensive ramp in your van.
Professional and user-friendly design
Airflex Pro is big enough to really impress your customers, but is easy to manoeuvre and lightweight compared to other machines in the same class. Airflex has huge 12″ wheels with built in shock absorbency and there’s a brake on the front caster (we think all extractors should have a brake but few do).
Tough and durable
The polyethylene casing is extremely tough and won’t delaminate like fibreglass can. The Airflex machine design also helps protect protruding components like the pump regulator, solution outlet and dump gate from damage.
Easy-reach, top mounted controls
Pressure regulator, gauge, and all main control switches are safely situated where you want them for easy access.
Built-in power sprayer system
With Airflex you can use the power of the pump to pre-spray even large areas quickly and easily. There’s no need to go to the expense of a separate electric sprayer.
Built-in auto-feed system
With Airflex, you can hook directly into water tanks mounted in the van, reducing set-up times significantly. There’s no need to install a separate pump. Just drop the special hose into an external tank and you’re ready to go.
Optional exhaust silencer for whisper quiet operation
Attach the optional big bore exhaust silencer and reduce machine noise considerably. You can also use this to vent moist air away from the working area, which further improves drying times and indoor air quality.
With the exhaust silencer attached, you can stand right next to Airflex Pro and talk without needing to raise your voice – now you also have one of the quietest professional extractors on the market.
Easy low cost servicing and parts
Airflex machines are incredibly easy to look after. The motor housing is accessed in seconds. A vac motor can be changed in 10 minutes. Pump heads can be changed in as little as 10 minutes – a job that can take 1.5 hours on some machines! This means less downtime and lower servicing costs.
Because Airflex machines are manufactured in the UK, we always have large stockpiles of parts. When you need a part we will have it, which isn’t always the case with imported machines.
The Airflex Big Airflow System
During the development of Airflex, extensive specialist advice was taken both independently and from Lamb Ametek – the World’s leading manufacturer of vacuum motors.
As a result, from the 2” hose port to the 4” exhaust, every inch of the Airflex internal vacuum system has been assessed and optimised to improve vacuum performance.
The result is a highly efficient airflow optimised extractor that gives you the best possible performance from your Airflex vacuum system. Airflex machines can be used with either 1.5” hose for convenience, or 2” hose for maximum airflow.
Local servicing network
Cleansmart utilises a National network of repair engineers. This means you can normally have your machine serviced locally, minimising both your downtime and servicing costs.
Read the reviews
If you scroll up this page on the left you will see customer ‘reviews’ link for recent reviews of this machine. You can also read some older Airflex reviews here which were published before we launched our new website.
Configure your machine spec
Use the configurator at the top of this page to spec your machine and get instant pricing.
Finance available on this machine click here for more info
View more professional carpet cleaning machines
Share your thoughts!
Let us know what you think...
Only logged in customers who have purchased this product may leave a review. Log in now
What others are saying
Related products
-
Prochem Steempro Powerplus
0 out of 5£3,695.00Original price was: £3,695.00.£2,956.00Current price is: £2,956.00. plus VAT Read more -
External Magma Inline Heater
5.00 out of 5£879.00Original price was: £879.00.£734.34Current price is: £734.34. plus VAT Add to basket -
Airflex Storm top-of-the-range machine starter package
0 out of 5£9,235.92Original price was: £9,235.92.£7,755.68Current price is: £7,755.68. plus VAT Add to basket -
Prochem Heat n Run Inline Heater
0 out of 5£825.00Original price was: £825.00.£660.00Current price is: £660.00. plus VAT Read more
steve-7173 –
How long have you been using this product? A few months
Bought an 800psi machine along with the CX15 wand back in May to allow us to take on some tricky commercial carpets as well as the run of the mill domestic jobs. Superb machine with some fab results on some oil drenched and trodden carpets at a plastic moulding facility we look after. The heater takes no time at all to get working (I’d be suprised if it took a full minute) and the power of the pump through 75ft hoses, even through the CX15 wand (which is a beefy tool) is to be admired. We’d previously subbed out this particular job to a company with a truck mount, who could not achieve the same results. Also bought a vac booster, but have yet needed to actually use it! Online training course is good and helpful, but looking forward to a ‘real life’ course after this Covid milarky has subsided. 10/10 for the machine and an A* for aftersale support. Great investment. Photos to follow.
Upvote if this was helpful (1) Downvote if this was not helpful (0) Flag for removal